Procom RD-C Instrucciones de operaciones

MICRO GROW GREENHOUSE SYSTEMS, INC 26111 YNEZ RD., SUITE C-4, TEMECULA, CA 92591 PHONE (909)-296-3340 FAX (909)-296-3350 Revision 1.2

9 The Solar Adjustment feature allows the grower to adjust the cooling temperature setpoint up or down depending on how intense the solar level is.

10 SET HEATING The SET HEATING mode will be used to set the desired Heating stage temperature separations and differentials. The internal time del

11 The Solar Adjustment feature allows the grower to adjust the cooling temperature setpoint up or down depending on how intense the solar level is.

12 SET VENTILATION The SET VENTILATION mode is used to set the number of desired stages of the vent openings, the desired position of each stage,

13 Link Vent 1 to Override Inp (NO) Use this setting if any override inputs are in use. Override inputs can come from the use of a Weather Station,

14 SET SHADING The SET SHADING mode will determine the total number of shade opening stages, the system timing for the shade system, the solar le

15 Go to (0) % if (Mode) = (Eve) Enter the percent of the close position that you want the shade system to go to during heat retention. Also, sel

16 SET FOGGING The SET FOGGING mode is used to set the temperature and humidity differentials and the system timing for the fogging output. The gr

17 SET HEAT VALVES The SET HEAT VALVES mode is used to set the criteria for any modulating heat valves in use. In the event that hot water valves

18 Reference Temp: (Air Temp 1) Set the desired input to be used as the reference temperature or NONE if no reference temperature is desired. If CO

1 INSTALLATION PROCEDURES GROWMASTER SERIES OF CONTROLLERS PANEL MOUNTING Mount the control panel in an accessible location. Make sure that the l

19 PULSED HEATING VALVES Use The Below Settings Only if You are Using a “Pulsed Heat Valve” The Pulsed Heat Valve is Different Than a “Hot Water Va

20 SET DEHUMIDIFY The SET DEHUMIDIFY mode is used to enable or to disable the dehumidify functions of the control. The run time of the immediate a

21 SET CROP LIGHTING The SET CROP LIGHT mode allows the grower to set time delays, solar levels, and other criteria for the crop lighting outputs.

22 SET CO2 All the desired CO2 settings will be made in the SET CO2 mode. Linking of CO2 to a Ventilation or Cooling output, setting of different

23 SET ALARM All of the desired alarm settings will be made in the SET ALARM mode. Set the high and low alarm settings for the individual sensors.

24 8GROWMASTER PROCOM OUTPUTS24 VAC POW ER INPUT1224 VAC POW ER INPUTFOR ALL LOADS24 V A C C O M M O NFUSED ACALARM OUTPUTPOW ER FAILUREFUSED 24

25 ALL CORRECT LOAD CONTACTORS AND CONTROL RELAYS ARE AVAILABLE FROM M ICRO GROW GREENHOUSE SYSTEMS.DIST R IBUTOR OR CALL M ICRO GROW FOR REQUIRED

26 Drawn byProjectGHSEN SO RACPhone 909.296.3340 Fa x 909.296.3350MICRO GROW GREENHOUSE SYSTEM S, INC.26111 Ynez Road, Suite C-4Te m e c u la, CA 92

27 +5 VD C REDDrawn byProjectGH1W EATH ERM ASTERDIGITAL OVERRIDECONNECTION TO PROCOM /GROW COMFUSE2Phone 909.296.3340 Fa x 909.296.3350MICRO GROW GR

28 N/ADistributorN/ADate11/28/01Order IDDIGITAL OVERRIDE44312234856347OUTPUT #1ACCOM1GREEN312OUTPUT #8OUTPUT #2OUTPUT #3OUTPUT #4OUTPUT

2 WIRING METHODS Always use stranded wire when connecting cables or conductors to the actual circuit board of the control panel. This will allow f

29 11/28/01GROWLINK CONV. BO X TO MULTI GM'S W/REPEATERGROWMASTER 2GROWMASTER 1COMMUNICATION CABLE IS 22 A W G , TW IST ED2 PA IR INDIVIDUALLY

30 TO SENSORTERM INALSE N SO R INPUTTRANSFORMERPROCOM SENSORSLOCATE SENSOR IN THE CENTER OF THEAW AY FROM D IRECT CONTACT W ITHGREENHOUSE M ETAL P

31 N/AOrder IDN/A11/29/01DateDistributorPROCOM HO T WATER & SO IL TEM P SEN SO RSBLACKPRO BESO IL TEM P.REDTe m e c u la, CA 9259126111 Ynez Roa

32 TO CONTROLSEN SO R CO N N E CT IONSFACTORY SETTINGS.INSTRUCTIONS TO CHANGESEE M ANUFACTURER'SALARM SET TO 1000 PPM.RELAY CONTACTS 1 Amp M A

33 NOTE: LOCATE AM PLIFIER CIRCUIT BOARDWITHIN PROCOM ENCLOSURE. SECURELYM OUNT TO BACK OF ENCLOSURE.SH L D /GNDSIG INTO PROCOM CONTROLSENSOR CONNE

34 LI-COR QUANTUM PAR LI-190NOTE: LOCATE AM PLIFIER CIRCUIT BOARDWITHIN PROCOM ENCLOSURE. SECURELYM OUNT TO BACK OF ENCLOSURE.SH L D /GNDSIG INTO

35 PHOTOCELLSEN SO R INPUT TERMINAL STRIP7PHOTOCELL REDPHOTOCELL COM MON BLACKWITH ALL PROCOM UNITS. IF INS

36 Drawn byProjectGHPhone 909.296.3340 Fa x 909.296.3350MICRO GROW GREENHOUSE SYSTEM S, INC.Tem ecula, CA 9259126111 Ynez Road, Suite C-4

37 TO LOADDrawn byProjectGHCIRCUIT #2Phone 909.296.3340 Fa x 909.296.3350MICRO GROW GREENHOUSE SYSTEM S, INC.AND LESS THAN 30 AMPSFOR LOADS OVER 10

38 INTERLOCKELECTRICALT1L1CONTACTOR USED FOR 2 SPEED FANST YPICAL CONNECTION FOR 2 SPEED LOAD24 VAC COMMONROUTE TOLOW -SPE E D FANHIGH-SPE E D FAN

3 GROWMASTER PROCOM OPERATING INSTRUCTIONS PROCOM SERIES The PROCOM Series is a completely programmable greenhouse computer system. Any output may

39 LIMITED WARRANTY Micro Grow Greenhouse Systems, Inc. warrants that all of the products Micro Grow Greenhouse Systems, Inc. manufactures are free

4 PROGRAMMING SWITCHES There are three main programming switches located on the Growmaster front panel. These are: RUN-SET SWITCH RUN-Puts the c

5 RUN REPORTS The RUN REPORTS mode allows the grower to run selected reports on the sensor history. 1. Enter the RUN REPORTS mode. 2. Use the PRIO

6 GROWMASTER PROCOM SET UP SET SYSTEM The SET SYSTEM mode is used to set the system clock and date, manually view the system's sunrise and su

7 Remote ID Code: (0) Not applicable if not using the GROWLINK program. Set the ID code here for the Growlink remote PC program available from Mic

8 SET COOLING The SET COOLING mode will be used to set the desired cooling stage temperature separations and differentials. The internal time dela